Anti-vibration benches
The anti-vibration benches can be made as standalone versions or can be integrated within a FLEXA or EASYLAB bench model.
They consist of an internal metal structure supporting a granite anti-vibration plate, equipped with a set of elastomer anti-vibration devices. The structure is leveled using lower adjusting feet.
The external casing is made of refined panels equipped with rounded-corner ABS and is completely independent from the anti-vibration structure/plate.
Contact us
Aspiration hoods Pratika DS series
Pratika DS features a technical side for equipment and services, thus completely freeing the work surface even from any trays.
SAFETY, THE PRIMARY PROJECT OBJECTIVE
The chemical hood is primarily a safety device that must allow the operator to work in total peace of mind regardless of the danger of the substances handled.
For this reason, operator safety is at the top of the list of objectives that Ferraro Arredi Tecnici has decided to pursue with the hood project.
In addition to the various certifications obtained, which place them among the most “awarded” hoods on the European market, test reports on containment values clearly show the quality of this safety project, synonymous with product development quality and also of the carefully selected materials to build a winning product.
QUALITY OF MATERIALS AND CONSTRUCTION FEATURES
The hood consists of a metallic supporting structure in Class “0” fire reaction with full-height load-bearing side shoulders made of steel with protective polyester coating, specifically aimed at laboratory processing.
The rear part of the work compartment consists of a double sheet of integral fireproof Labgrade laminate in class1, which forms a double suction chamber equipped with various suction slots capable of absorbing heavy gases at the bottom and light gases at the top.
The upper ceiling made of integral Labgrade laminate consists of a transparent polycarbonate panel placed in the center and has a neon lamp with IP 65 protection at the top, therefore outside the work compartment as required by the reference standard.
On the sides of the lamp, there are two explosion-proof hatches made in Labgrade laminate, which will allow the venting of a possible shock wave in the event of small explosions under the hood.
The castellation allows quick replacement of the work surface by simple removal, without the need to dismantle the supporting structure.
The front part of the hood will consist of an appropriately counterweighted aluminum frame with two horizontally sliding 3+3 safety type glasses. Even in the horizontal scrolling condition, in any position where the two glasses are located, the hood is certified according to EN14175, so the operator can perform operations that are facilitated by the horizontal scrolling of the double glass in an absolutely calm and guaranteed manner.
The work surface is positioned in a standard configuration at a height of 90 cm from the floor and can be made with different types of work surfaces. In the distillery version, the height of the floor surface is reduced to 50 cm.
The water and gas nozzles are positioned on the back panel of the hood, while the remotes of the same and the electrical sockets are housed and on the front panel below the work surface, thus leaving ample horizontal space to the work surface which will be used to the fullest possibilities.
The base is tied to the hood sides but does not constitute a load-bearing structural element for the castellation, this in order to be possibly extracted in the future by reconfiguring the hood as walk-in (reconfiguration and furniture flexibility).
The suction intakes are designed and made to avoid the formation of turbulence or air vortices, and the suction intakes fit perfectly into the back wall. The duct that collects the intakes is in turn connected to the suction system. The air intakes are sized to achieve a balanced internal distribution of air and a correct speed in the ducts.
COLORS
It is possible to customize with chosen colors the cabinet of the hood as well as the Ferraro logo, which can reflect the color choice made for the undercounter. The colors available in the catalog are anthracite, burgundy, light gray, classic blue, and white.
The painting of the metallic structure will externally present an innovative and different color, abandoning the old Ral7035 and aiming at the development of a product in line with modern design.
Contact us
Aspiration Hoods Pratika series
Pratika replicates, with a modern and functional look, the traditional work concept that places services under the surface.
SAFETY, THE PRIMARY PURPOSE OF THE PROJECT
The chemical hood is primarily a safety device, which must allow the operator to work in complete peace regardless of the hazard of the substances handled.
For this reason, the safety of the operator is at the top of the list of objectives that Ferraro Arredi Tecnici decided to pursue with the hood project.
In addition to the various certifications obtained, which rank it among the most “rewarded” hoods on the European market, test reports on containment values clearly show the quality of this safety project, synonymous with quality in product development as well as the materials carefully selected to build a winning product.
QUALITY OF MATERIALS AND CONSTRUCTION FEATURES
The hood consists of a supporting metal structure in Class “0” fire reaction with full-height load-bearing side panels made of steel with a protective polyester coating, specifically targeted for laboratory processing.
The rear part of the workspace consists of a double sheet of integral Labgrade fireproof laminate in class1, which forms a double aspirating chamber equipped with various suction slots capable of absorbing heavy gases at the bottom and light gases at the top.
The upper ceiling made of integral Labgrade laminate consists of a transparent polycarbonate panel located in the central part and has, at the top and therefore outside the workspace as required by the reference standard, an LED lamp with an IP 65 protection rating.
On the sides of the lamp, there are two explosion-proof hatches also made of Labgrade laminate, which will allow the venting of a possible shock wave in case of small explosions under the hood.
The framing allows the quick replacement of the work surface by simple removal, without requiring the disassembly of the supporting structure.
The front of the hood will consist of a counterbalanced sliding aluminum frame equipped inside with two horizontally sliding 3+3 safety type glasses. Even in horizontal scrolling conditions, the hood is certified according to EN14175, so the operator can perform operations facilitated by the horizontal movement of the double glass in an absolutely calm and guaranteed manner.
The work surface is positioned in a standard configuration at a height of 90 cm from the floor and can be made with different types of work surfaces. In the distillery version, the height of the surface from the floor is reduced to 50 cm.
The nozzles for water and gas are located on the back panel of the hood, while the remote controls for them and the electrical outlets are only housed and on the front panel below the work surface, thus leaving ample horizontal space on the work surface that will be used to its fullest potential.
The base is attached to the hood sides but is not a structural load-bearing element for the framing, this in order to possibly be extracted in the future by reconfiguring the hood as a walk-in (reconfiguration and furnishing flexibility).
The intake ports are designed and made to prevent the formation of turbulence or air vortices. The duct that gathers the intakes is in turn connected to the aspiration system. The air intakes are sized to create a balanced internal air distribution and a correct speed in the ducts.
COLORS
It is possible to customize the hood cabinet with chosen colors as well as the Ferraro logo, which can reflect the color choice made for the undercounter. Available in the catalog are anthracite, burgundy, light gray, classic blue, and white.
The painting of the metal structure will externally present an innovative and different color, abandoning the old Ral7035 and aiming at the development of a product in line with modern design.
Contact us
Benches for laboratories Series Easylab
Gamba C
La serie di banchi EasyLab è nata dall’esigenza dei nostri clienti di avere a disposizione un sistema di arredo semplice e modulare che permetta di arredare gli spazi a disposizione con ridotte misure di ingombro in profondità, impiegando comunque materiali e componenti di elevato grado qualitativo, certificati e nati per un impiego operativo giornaliero.
I banchi EasyLab sono proposti sia in tipologia sia a parete che centrale attrezzati con vano tecnico posteriore porta impianti disponibile in varie soluzioni a partire da filo piano di lavoro fino alle soluzioni con paretina posteriore attrezzata per aggancio pensili, mensole e accessori soddisfacendo così diverse necessità di impiego.
Gamba U
Contact us
Benches for laboratories Series Flexa
The integrated Flexa system uses an advanced technical rear module that’s deep and highly flexible, allowing for differentiated equipment solutions in every area of the bench. It uses interchangeable modular panels that are simply attached to the module structure, which can accommodate electrical outlets, taps, and gas dispensers. These can easily be moved from one position to another, thanks also to flexible connection systems that are easy to reconfigure. The Flexa series is equipped with a complete set of shelves for objects, chemical holders, overhead cabinets, and multi-purpose bars for attaching accessories, computer monitors, and localized exhaust arms.
The Flexa benches are offered in both wall-mounted and central types and can come in various heights (910, 1200, 1420, 2250mm.) with the option to have modular utility panels at different levels or to affix outlets and dispensers to a tower on the 910mm band level with the worktop. In both cases, however, this module remains independent and self-supporting, allowing for potential use separate from the bench structure. The ample internal depth of this solution allows for easy equipping of those benches, especially in central configurations, where there’s a need for numerous electrical outlets and fluid/gas dispensers to serve equipment placed on the worktops. Its high storage capacity combined with the system’s great flexibility make it a powerful work tool. Each module is completely accessible at every level for maintenance without the need for tools or specialized personnel.
Contact us
Satellite Systems
Mobile satellite systems.
With the Kinesis series, the laboratory world travels into the future, allowing the creation of instrumental areas with an entirely new concept.
[…] Read More
Benches for laboratories
We offer a wide range of modular benches that arise from the need to set up a laboratory in a flexible manner and especially reconfigurable in the future. The philosophy that has guided our project is based on the user’s needs: to design and create a laboratory in a flexible and innovative manner, while still preserving standard and modular furniture elements.
[…] Read More
Chemical hoods
Practical use, certified materials, strong lightness and visibility of the work area linked together with an excellent managing of the aspiration levels, check of the fumes and energy saving make our chemical hoods an easy, but efficient work instrument.
[…] Read More